Irondequoit Electrical Company handles electrical work for homeowners, landlords, property managers, and small commercial clients throughout Irondequoit and the surrounding Monroe County area. From a breaker that won't reset at midnight to a planned EV charger installation on a weekend renovation schedule, we take the full range of calls. That means everyday repairs, panel upgrades, new circuits, lighting projects, and wiring work of every size. We power your home. We protect your circuits. We earn the call.
Whether you're dealing with sparks from an outlet, a section of the house that's gone dark, or a remodel that needs new wiring from scratch, the process starts the same way.
Call (585) 822-6289 and get a quote before anything is scheduled.
No matter what's going wrong with your wiring, the symptoms usually point to something specific once the wiring gets a proper look. Flickering lights throughout the house, dead outlets, a breaker that trips the moment you reset it, a burning smell near the panel or a receptacle, sparks when you plug something in - these are the calls we get most often, and each one has a traceable cause.
When the electrician arrives, the real work begins. The visit covers a full assessment of the symptom, tracing it back to the source, and scoping the repair before any work starts. The scope of the electrical work is priced before it starts, so you know what you're agreeing to.
Where outlets or circuits are involved, we address GFCI and AFCI protection as part of the repair. Ground-fault and arc-fault breakers are standard in modern electrical work, and upgrading to them during a repair visit is often the right call for older wiring or unprotected circuits. One call gets the problem looked at properly.
Before a small wiring issue turns into a hazard, it's worth getting the outlets and switches in your home checked and updated. We install standard outlets, GFCI receptacles, AFCI outlets, and USB combination units. Switch replacements, dimmer installations, and three-way switch wiring are all part of the same category of work, and we handle them for single rooms or whole floors.
Ceiling fan installation fits naturally here too. Whether you're replacing an old fixture or adding a fan where there was only a light box before, we wire the circuit and mount the unit properly.
For finished spaces, we install recessed LED lighting, under-cabinet lighting in kitchens, and fixture replacements throughout the home. No pressure and no gimmicks, just safe, solid wiring from the panel to the fixture.
Renovation and remodel work is a big part of what we do. Basement finishes, garage wiring, room additions, and shed circuits all require electrical work that has to be done to code. We handle the rough-in and the finish work so the project moves forward without delays from the electrical side. We'll handle the wiring so you don't have to.
Exterior lighting serves more than one purpose. It adds curb appeal, improves safety on walkways and driveways, and discourages unauthorized access to both residential and commercial properties. We install outdoor lighting fixtures, landscape lighting circuits, security lights, and motion sensor lights for homes and businesses across Monroe County.
Exterior wiring has to be run and weatherproofed correctly for this climate. Monroe County winters are not forgiving to shortcuts in outdoor electrical work. Every exterior circuit we run is properly grounded and weatherproofed to meet the code requirements for this region. Call now and we'll get the power back where it belongs.
This area has every kind of panel and circuit in it, and older homes in Irondequoit sometimes still carry knob-and-tube wiring or aluminum branch-circuit wiring that needs to be addressed. Knob-and-tube replacement and aluminum-wiring remediation are jobs we take on regularly. A pre-purchase electrical inspection or a safety inspection often surfaces these issues, and that's a natural point to discuss rewiring options.
Dedicated circuits are another common request. Dryer outlets, electric range circuits, refrigerator circuits, and the dedicated electrical supply that feeds a heating or cooling unit all require their own circuit sized for the load. We also wire dedicated circuits for hot tubs and large appliances that can't share a circuit without tripping the breaker.
Panel and wiring work is finished to code, which matters when a property goes through inspection or changes hands. Electrical safety inspections give landlords and property managers a clear picture of what the system can handle and what needs attention before it becomes a problem.
We take calls from single-family homeowners, multi-unit landlords, property managers, office buildings, retail spaces, and small businesses. The electrical needs vary, but the process is the same: the scope is confirmed, the price is set, and the work is done to code.
For landlords and property managers, scheduling is straightforward. We show up, assess the system, and complete the work so it passes inspection. Code violation repairs and failed electrical inspection corrections are jobs we handle regularly. If a unit has been flagged for a wiring issue or an outdated panel, we can scope the repair and get it on the calendar.
Hire local and the wiring is done by someone who knows the area. The person who answers the phone knows this trade and can help you scope the job before the visit is ever scheduled. Call now and we'll set the appointment.
Monroe County winters are hard on electrical systems. Long stretches of sub-freezing temperatures, ice storms off Lake Ontario, and multi-day outages are part of life here. The homes and businesses in this area have specific electrical needs that go beyond what a warmer market would ever see. The three services below reflect what comes up most in this region.
When a winter storm knocks out power in Irondequoit, it can stay out for days. We handle the electrical side of generator installation: the transfer switch, the dedicated circuit from the panel to the generator connection point, and the wiring that keeps the load managed and prevents backfeed to the grid. We work with both standby and portable generator hookup configurations. The generator itself is the homeowner's equipment or comes from a separate supplier. Our scope is the wiring and the transfer switch that makes it safe and functional.
Older housing stock in Irondequoit often carries panels that were sized for a different era. A 100-amp service that handled a home in the 1970s does not handle an EV charger, an electric range, and backup heating loads at the same time. We replace breaker panels, upgrade from 100-amp to 200-amp service, install subpanels, and handle service-entrance and meter upgrades along with the load calculations that determine what the system needs. Whole-home surge protection is a natural addition at panel upgrade time, and we install it at the panel level while the work is already open. The work area is left as it was found.
Heat tape, sometimes called heat cable, runs along rooflines, in gutters, and around exposed pipes to prevent ice damming and freeze damage. Irondequoit's proximity to Lake Ontario means heavy lake-effect snow and freeze-thaw cycles that make ice dams along rooflines a routine winter problem. A properly wired dedicated circuit is what makes heat tape work reliably and safely. We run the circuit and wire the connection point. The tape or cable product is the homeowner's or a contractor's item. If you're preparing for winter and the heat tape circuit isn't in place yet, this is the time to get it scheduled.
Level 2 EV charger installation starts at the panel. We assess the available capacity, run a dedicated 240-volt circuit to the garage or charging location, and install the outlet or hardwired connection the charger requires. If the panel needs an upgrade to support the load, we scope that work at the same time. A growing number of Irondequoit homeowners are adding EVs and want the charging infrastructure at home rather than relying on public stations.
Whole-home surge protection works at the panel level, catching voltage spikes before they reach the circuits and devices throughout the house. It's particularly relevant after a panel upgrade or new wiring project, when the system is already open and the addition is straightforward. We'll handle the wiring so you don't have to.
Scheduling a service call is simple, and so is the pricing conversation. When you call, you get a clear explanation of what the work involves and what it costs before anything is scheduled. The scope is confirmed on the call, and you're told what it covers. There are no ambiguous charges added after the job is complete.
We get asked regularly what an electrician costs, what a call-out fee looks like, and how the pricing works for different types of jobs.
The answer is always the same: call (585) 822-6289 and ask.
The rate is set before the visit, and you know what you're agreeing to before the electrician arrives.
Call in the morning. Talk it through. Know the options by the end of the call.
Irondequoit is where we focus, but we take calls from neighboring communities across Monroe County as well. If you're in Webster, Penfield, Brighton, Pittsford, Greece, Henrietta, or Rochester, call and we'll confirm whether your address falls within the current service area.
We're available every day from 6:30 AM to 8:00 PM. Call now and we'll get the power back where it belongs.
The most common signs are breakers that trip under normal loads, a panel that feels warm to the touch, circuits that cannot support the appliances plugged into them, and a fuse box or older breaker panel that has not been updated since the home was built. If you are adding an EV charger, electric range, or significant new load to the home, a load calculation will tell you whether the current service can handle it.
Call (585) 822-6289 and we can talk through what is happening.
A transfer switch is a device wired between the utility connection and the generator that keeps the two power sources electrically separated. Without one, a generator feeding power back into the utility line creates a serious hazard for anyone working on the line during an outage. We install transfer switches for both standby and portable generator configurations, and the switch is tested before the job is closed out.
Generator sizing depends on which circuits you need to power during an outage: lights, heat supply, refrigeration, and medical equipment all draw different loads. Our scope is the electrical hookup: the transfer switch, the dedicated circuit from the panel to the generator inlet, and the wiring that keeps the load managed safely. The generator itself comes from the homeowner or a separate supplier. Call us and we can explain what the electrical side of the installation involves for your specific setup.
Heat tape requires a dedicated circuit run to the appropriate location, weatherproof connections, and a GFCI-protected outlet rated for the application. Because the system runs continuously through the coldest months, the wiring has to meet the full demands of that load from the start. We handle the circuit and the connections so the heat tape operates reliably when temperatures drop.
A burning smell near an outlet, switch, or panel, sparking from a receptacle, a panel that is warm or making a buzzing sound, or a partial power loss that cannot be explained by a tripped breaker are all situations that call for immediate attention. We are available every day from 6:30 AM to 8:00 PM.
Call (585) 822-6289 and describe what you are seeing.
Breakers that trip frequently, a panel that feels warm, a burning or plastic smell near the panel, breakers that will not hold their reset, and visible corrosion or scorch marks inside the panel door are all warning signs. Fuse boxes where fuses have been replaced with higher-rated fuses than the circuit is designed for are a related concern in older homes. Any of those findings warrants a panel assessment.
A targeted repair makes sense when the fault is isolated and the surrounding wiring is in good condition. A partial or full rewire is the right call when the wiring type itself is the problem, such as active knob-and-tube, aluminum branch-circuit wiring with connection issues throughout, or a home where multiple circuits are failing in the same pattern. We assess the wiring condition during the visit and explain what each option involves before any work is agreed.
An outlet that does not respond to plugged-in devices, one that feels warm to the touch, or one with discoloration or scorch marks around the face plate are all signs of a problem that needs to be looked at. A warm or discolored outlet can indicate a loose connection, an overloaded circuit, or a wiring fault. Stop using it and call to get it assessed.
A switch or outlet that buzzes, crackles, or makes noise when in use has a connection problem that needs to be addressed. Loose connections generate heat and can cause arcing over time. A buzzing switch is not a nuisance issue. It is a wiring fault that should be diagnosed and repaired.
Yes. GFCI outlets can be installed in ungrounded circuits and provide ground-fault protection even without a ground conductor. They are required to be labeled as ungrounded when installed this way. Running a new ground conductor back to the panel is another option where the wiring allows for it. We assess the existing wiring and explain which approach applies to your situation.
Exterior circuits require weatherproof boxes, covers, and fittings rated for outdoor exposure. In Monroe County's climate, those connections take a beating from ice, freeze-thaw cycles, and moisture, so the materials and methods matter more than they would in a milder region. Every exterior circuit we run is properly grounded and weatherproofed to meet code requirements for this area.
The most common cause is a difference between what was described on the call and what the electrician finds on site. Older wiring types, a panel in worse condition than expected, or a fault that turns out to be in a location that requires more work to access can all affect the scope. If the scope changes, we explain what was found and what addressing it involves before any additional work continues.
Clear access to the panel is the most important step. If the panel is in a utility room, basement, or closet, make sure it is reachable before the electrician arrives. For outlet or switch work, move furniture or objects away from the work area. If you have a diagram of the home's circuits or know which breakers control which rooms, that information is helpful but not required.
Irondequoit Electrical Company handles electrical repairs, panel upgrades, new circuits, lighting, wiring, generator hookups, EV charger installation, and everything in between for residential and commercial properties throughout the area. Whatever the job involves, the process starts with a call.
We're available every day from 6:30 AM to 8:00 PM.
Call (585) 822-6289 to get a quote. We'll handle the wiring so you don't have to.
From a tripped breaker to a full panel upgrade, we handle the electrical work that keeps Irondequoit homes and businesses running safely. Every job starts with a clear scope and a confirmed price before anything is scheduled. The table below covers what each service includes, who it fits, and what is practical to know before you call.
| Service Type | Scope of Work | When You Need It | Worth Knowing |
|---|---|---|---|
| Electrical Panel & Service UpgradesMost Popular | 100-amp to 200-amp service upgrades, Subpanel installation, Load calculations, Whole-home surge protection at the panel | Homes adding an EV charger, electric range, or large new load that the current service cannot support | Panel work is finished to code and is the right time to add whole-home surge protection while the panel is already open. |
| Electrical Repairs & Troubleshooting | Flickering lights and dead outlets, Tracing faults to the source, GFCI and AFCI protection upgrades, Burning smells and sparking receptacles | Any homeowner or property manager dealing with an unexplained electrical symptom | Most symptoms point to a traceable cause once the circuit is assessed. We scope the repair before any work begins. |
| Heat Tape Installation | Dedicated circuit for heat cable, GFCI-protected weatherproof outlet, Roofline and exposed pipe circuit wiring | Homes near Lake Ontario where ice damming and freeze-thaw cycles are a recurring winter problem | Heat tape needs a properly wired dedicated circuit to operate reliably and safely through the coldest months. The tape or cable product is the homeowner's item. |
| Backup Generator Installation | Transfer switch installation, Dedicated circuit from panel to generator inlet, Standby and portable hookup configurations, Backfeed prevention wiring | Irondequoit homeowners preparing for multi-day winter outages from lake-effect storms | Our scope is the wiring and the transfer switch. The generator itself comes from the homeowner or a separate supplier. |
| Dedicated Appliance Circuits | Dryer and electric range circuits, Refrigerator and large appliance circuits, Electrical supply for heating and cooling units, Hot tub and workshop circuits | Any appliance or load that cannot share a circuit without tripping the breaker | Each dedicated circuit is sized for the specific load it feeds. We handle the wiring and confirm the panel has capacity before the circuit is run. |
| Lighting Installation | Recessed LED and fixture replacement, Under-cabinet kitchen lighting, Outdoor and security lighting, Motion sensor and landscape circuits | Renovation projects, exterior safety upgrades, and rooms that need updated lighting | Exterior wiring in Monroe County requires weatherproof fittings and materials rated for freeze-thaw conditions. |
| Electrical Safety Inspections | Full system assessment, Wiring condition review, Panel capacity evaluation, Code violation identification | Landlords, property managers, and buyers or sellers of older Monroe County homes | An inspection gives a clear picture of what the system can handle and what needs attention before it becomes a problem at a tenant's call or a home sale. |
| Breaker & Fuse Repair | Breakers that trip and won't reset, Fuse box assessment, Replacing failed breakers, Identifying overloaded circuits | Homes where a breaker keeps tripping or a fuse box has not been updated | A breaker that trips repeatedly under normal load is often a sign of a wiring fault or an undersized circuit, not just a bad breaker. |
| Wiring & Rewiring | Knob-and-tube replacement, Aluminum branch-circuit remediation, Basement and garage rough-in, Room addition and remodel wiring | Older Irondequoit homes with outdated wiring types or properties undergoing renovation | A pre-purchase electrical inspection often surfaces knob-and-tube or aluminum wiring concerns. That is a practical point to discuss rewiring options. |
| Outlet & Switch Installation | Standard and GFCI receptacles, AFCI outlets, Dimmer and three-way switch wiring, USB combination units | Rooms with outdated, ungrounded, or insufficient outlets and switches | Two-prong outlets in an older home are a sign the wiring deserves a look. GFCI outlets can be installed even on ungrounded circuits. |
| Ceiling Fan Installation | Replacing existing fixtures, Adding a fan where only a light box exists, Circuit wiring for new fan locations | Homeowners upgrading a room or adding airflow to a finished space | A standard light box is not always rated for a ceiling fan's weight and movement. We confirm the box and wire the circuit correctly. |
What causes breakers to trip repeatedly?
A breaker that trips under normal load is usually telling you something specific. The most common causes are a circuit carrying more load than it was sized for, a wiring fault somewhere along the circuit, a failing breaker that no longer holds its rated amperage, or a short in a device or appliance plugged into that circuit. Resetting the breaker and watching which device triggers the trip again is useful information to have when you call. We trace the fault from the symptom back to the source before recommending a repair.
Is the electrical work permitted and inspected to code?
Panel upgrades, service changes, new circuits, and rewiring work are the types of jobs that typically require a permit and a follow-up inspection by the local authority. We handle the work to code, and the scope of the job determines whether a permit is required. When you call to discuss the job, we can tell you what the permitting process looks like for your specific situation in Irondequoit or the surrounding Monroe County area.
How do I know if the wiring in my older home is safe?
Older homes in Irondequoit can carry knob-and-tube wiring, aluminum branch-circuit wiring, or ungrounded two-prong circuits, any of which may need attention depending on their condition and what the home's current electrical load looks like. An electrical safety inspection is the clearest way to get that picture. We assess the wiring type, the panel, and the circuit condition, then explain what each finding means and what the options are.
Faults Traced Before Anything Is Replaced
We assess the symptom and trace it back to the source before any repair is recommended. That means the work addresses the actual problem, not just the visible one.
What does an EV charger installation involve?
A Level 2 EV charger runs on a dedicated 240-volt circuit. We start by assessing the panel to confirm there is available capacity for the load. If the panel needs an upgrade to support the charger, we scope that work at the same time. Then we run the dedicated circuit from the panel to the garage or charging location and install the outlet or hardwired connection the charger requires. The charger unit itself comes from the homeowner or vehicle manufacturer. Call us and we can walk through what the electrical side of the installation involves for your home.
Do I need to be home during the electrical work?
For most jobs, yes. Access to the panel is required for nearly all electrical work, and the electrician will need to walk through the scope with whoever is responsible for the property. For landlords and property managers, we are used to coordinating with tenants and scheduling around their availability. Call us and we can work out the access logistics before the visit is set.
What do flickering or dimming lights usually mean?
Occasional flickering tied to a large appliance starting up, like a refrigerator or air handler, is normal and usually reflects a momentary voltage drop on a shared circuit. Persistent flickering, dimming that affects multiple rooms, or lights that flicker without any obvious trigger point to something that needs to be looked at. Loose connections, an overloaded circuit, or a panel issue are the most common causes. We assess the symptom and trace it to the source before recommending a repair.
Scope Agreed Before the Panel Is Opened
The scope of the electrical work is priced before it starts. You know what you are agreeing to before anything is scheduled or any work begins.
What is whole-home surge protection and is it worth adding?
Whole-home surge protection installs at the panel level and catches voltage spikes before they reach the circuits and devices throughout the house. It does not replace point-of-use surge strips, but it handles the large surges that those strips are not designed for, including spikes from utility switching and nearby lightning. It is a practical addition any time the panel is already open for an upgrade or new circuit work, since the installation is straightforward at that point.
What are aluminum or knob-and-tube wiring concerns I should know about?
Knob-and-tube wiring was installed in homes built before the 1940s and does not include a ground conductor. It can still function, but it was not designed for modern electrical loads, and insulation deterioration over decades is a real concern. Aluminum branch-circuit wiring was common in homes built in the 1960s and 1970s and expands and contracts at a different rate than the copper connections it meets, which can loosen over time and create heat at connection points. Both wiring types come up regularly in Irondequoit's older housing stock. We assess the condition and explain what addressing it involves.
Older and Newer Wiring Both Handled
Irondequoit's housing stock runs from knob-and-tube to modern 200-amp service. We work across all of it and explain what we find in plain terms.
How long does a panel upgrade or service change take?
A standard panel upgrade from 100-amp to 200-amp service typically takes most of a day. The time varies depending on whether the service entrance needs to be updated, whether a subpanel is involved, and what condition the existing wiring is in. We confirm the scope and the expected timeframe on the call before the job is scheduled, so you know what to plan for.
Can I add circuits for a workshop or garage without upgrading the panel?
It depends on what capacity the current panel has available. If there are open breaker slots and the service amperage can support the additional load, new circuits can often be added without a full panel upgrade. If the panel is full or the load calculation shows the service is already near its limit, an upgrade or a subpanel is the right path. We assess both the available capacity and the planned load before recommending which approach fits your situation.
How is GFCI protection handled in kitchens, bathrooms, and outdoor areas?
GFCI protection is required by code in kitchens, bathrooms, garages, outdoor areas, and any location near water. In older homes that were wired before those requirements existed, GFCI outlets can be installed on ungrounded circuits and still provide ground-fault protection. They are labeled as ungrounded when installed that way. We address GFCI and AFCI requirements as part of outlet and circuit work throughout the home.
Call (585) 822-6289 and we will walk through what your job involves, confirm the scope, and set the price before anything is scheduled.
(585) 822-6289