Sometimes the job that gets called in is a single outlet that stopped working, and the visit turns up something the outlet was only pointing at. A circuit drawing more than it should, a panel that has been running at its limit, wiring that was never quite right to begin with. That is a conversation worth having before anything is scheduled, and we have it plainly. We explain what the outlet repair involves, what the broader issue looks like, and what addressing it would take. The call is where that starts.
We handle the full range of residential and commercial electrical work for Rochester Institute of Technology and the surrounding area. Repairs, panel upgrades, rewiring, new circuits, lighting, EV charger installation, generator hookups, and everything in between.
Call (585) 822-6289 and get the scope and the price before anything is booked.
Some electrical problems are not the kind you schedule around. A burning smell near a panel, an outlet that sparks, a section of the house that has gone dark without an obvious cause. Those calls come in and we treat them as what they are. We are available every day from 6:30 AM to 8:00 PM, and we take short-notice work when the schedule allows.
For tenants and businesses that have to stay operational, the visit is planned around what the space needs. Work that can be sequenced so one section stays live while another is addressed is handled that way where the job allows. The scope is confirmed before the electrician arrives, so the visit goes in knowing what it is there to do.
Scheduling a service call is simple.
Call (585) 822-6289, describe what is happening, and you get a clear picture of what comes next before you commit to anything.
Properties that have been standing for several decades carry wiring that reflects when they were built, not what a house needs today. Knob-and-tube wiring turns up in older structures, running through joists and walls in a way that was standard at the time and is now a concern in any space that has been insulated or modified since. It is not automatically a crisis, but it needs to be assessed honestly. Where it is active and feeding circuits that carry real loads, it is a conversation about replacement, not a patch.
Aluminum branch-circuit wiring from an earlier era is a separate issue. The wiring itself is not the problem. The connections are. Aluminum expands and contracts differently from copper, and connections that were made without the right materials or methods work loose over time. Every connection point needs to be addressed, not just the ones that have already shown symptoms.
Two-prong outlets in an older home are a sign the wiring deserves a look. They are not a danger by themselves, but they tell you the circuits feeding them were never grounded, and that is worth knowing before you add load to them.
Not every older installation needs to come out. A circuit that is properly sized, correctly connected, and not carrying a load it was never designed for can stay in service. The assessment tells us which is which. Where a rewire is the right call, we scope it clearly so you know what the project involves before it starts.
Panel and wiring work finished to code is what every job here comes back to. That matters when a property is inspected, when it changes hands, or when a tenant or occupant needs to know the system is sound.
The price for electrical work is set on the call, before a visit is scheduled. For straightforward jobs, the quote covers the work as described and what that involves. For jobs where the scope depends on what is found on site, we explain the range and what would move it in either direction.
Three things tend to change a quote once the work is underway. What the fault actually turns out to be, once it is traced to its source. What has to be opened up to reach it, especially in finished walls or ceilings where access takes time. And whether the existing circuit or panel can carry the change being made, or whether that needs to come up first.
Load calculations are part of any panel upgrade or new circuit addition. That is how we confirm the system is sized for what it is being asked to do, not just for what it is doing today. The scope of the electrical work is priced before it starts, so you are not agreeing to something open-ended.
In properties like those in Rochester Institute of Technology, the panel is usually in a basement, a utility room, or a garage. Clear access to it before the electrician arrives is the single most useful thing a property owner can do. A panel that takes twenty minutes to reach through stored equipment is twenty minutes off the work itself.
Basement panels often share space with water heaters, HVAC equipment, and storage. If the panel door can be opened fully and there is room to work in front of it, the visit goes faster. If the space is tight, knowing that ahead of time helps us plan the visit correctly.
Garage panels are common in properties where the original service entrance was run to the attached structure. They are usually more accessible than basement installations, but they sometimes serve a subpanel arrangement where the main service is elsewhere on the property. Knowing which is which before the visit is part of the scoping conversation. What a job like this usually involves is described on our wiring and panel services page.
Matching parts and fittings to what is already in a property is a routine part of electrical work. Older panels use breaker types that are no longer standard, and sourcing the right replacement matters. Installing a breaker that is not rated for the panel it goes into is not a fix. It is a new problem.
When a component has to be ordered rather than fitted the same day, we tell you that on the call or during the visit, before the job is left incomplete. For obsolete equipment where a direct replacement is not available, the options are explained so you can decide how to proceed. Sometimes the right answer is a panel upgrade rather than a hunt for a part that is no longer made. That conversation belongs in the visit, not after the fact.
No pressure and no gimmicks, just safe, solid wiring and a straight answer about what the job actually requires.
Rewiring comes up when the wiring type itself is the issue, not just a single fault. A home where knob-and-tube is still active in multiple circuits, or where aluminum wiring connections have been found in poor condition throughout, is a candidate for a partial or full rewire. We scope the project by what is actually present, not by a general estimate of age or size.
A 240-volt circuit for a range, wall oven, or dryer is a dedicated run from the panel, sized for the appliance load. If the circuit does not exist, or if the existing one was wired for a different appliance, it needs to be run correctly before the appliance is connected. This is one of the more common calls we get when a property is being updated or when a tenant or new owner brings in different equipment.
Fixture replacement is straightforward work when the existing wiring is sound. Recessed LED installation, under-cabinet lighting, and ceiling fixture swaps all fall into this category. Where the existing wiring at the box is not in good condition, or where the fixture requires a circuit the current wiring cannot support, that comes up during the visit and is addressed before the fixture goes in.
Workshop equipment draws significant load, and most residential panels were not sized with a welder or large compressor in mind. A dedicated circuit for that equipment is the right approach, sized for the draw of the specific tool. If the panel does not have the capacity, a load calculation tells us whether a service upgrade is needed before the circuit can be added. We handle both the circuit and the panel side of that conversation.
We serve Rochester Institute of Technology and the communities around it throughout Monroe County. That includes Henrietta, Chili, Gates, Brighton, and Scottsville.
If you are nearby and need electrical work looked at, call (585) 822-6289 and we will confirm whether your address falls within the current service area. We'll handle the wiring so you don't have to.
The mess depends on the scope. Outlet, switch, and fixture work produces very little disruption. Running new circuits through finished walls requires cutting access points, which produces dust and leaves openings that need to be patched afterward. We tell you what to expect before the work starts.
We leave the work area as it was found. That means debris from the job is removed, any access panels or covers that were opened are closed, and the space is left in the condition we found it. If the job runs across more than one day, we tidy the work area at the end of each session.
We plan the visit around what the space needs. Where the work can be sequenced so one area stays live while another is addressed, we do it that way. The scope is confirmed before the visit, so the work goes in with a clear plan rather than working it out on site.
Call (585) 822-6289 and we can talk through what the job involves and how the visit will be handled.
Yes. Kitchens and bathrooms have specific requirements for circuit quantities, GFCI protection, and the placement of outlets relative to water sources. These rooms are typically the most involved part of a rewire because of those requirements, and we address them as a distinct phase of the project.
Not always, but it depends on what the panel is currently carrying and whether it has the capacity for the new load. A load calculation is part of how we answer that question. If the panel can support the new circuit without being pushed past its rating, we run the circuit. If it cannot, we explain what a service upgrade would involve and what the project looks like from there.
Properties in and around Rochester Institute of Technology tend to be a mix of older residential construction and buildings that have been modified or added onto over the years. That combination produces the full range of wiring situations: outdated panel types, circuits that were added without a load calculation, and wiring types that need to be assessed before new work is layered on top.
Call (585) 822-6289 and describe what you are seeing, and we can tell you what it is likely to involve.
Electrical issues that get put off have a way of turning into larger jobs. A tripping breaker that keeps getting reset, a warm outlet that gets left alone, a panel that has been running at capacity for years. The call is short. Call in the morning. Talk it through. Know the options by the end of the call.
Call (585) 822-6289.
We are available every day from 6:30 AM to 8:00 PM. Reach Irondequoit Electrical Company directly at that number. There are no forms to fill out and no waiting for a callback.
Other towns where we take electrical work: Henrietta, Chili, Gates.
From a tripped breaker to a full panel upgrade, we handle the electrical work that keeps Rochester Institute of Technology homes and businesses running safely. Every job starts with a clear scope and a confirmed price before anything is scheduled. The table below covers what each service includes, who it fits, and what is practical to know before you call.
| Service Type | Scope of Work | When You Need It | Worth Knowing |
|---|---|---|---|
| Electrical Panel & Service UpgradesMost Popular | 100-amp to 200-amp service upgrades, Subpanel installation, Load calculations, Whole-home surge protection at the panel | Homes adding an EV charger, electric range, or large new load that the current service cannot support | Panel work is finished to code and is the right time to add whole-home surge protection while the panel is already open. |
| Lighting Installation | Recessed LED and fixture replacement, Under-cabinet kitchen lighting, Outdoor and security lighting, Motion sensor and landscape circuits | Renovation projects, exterior safety upgrades, and rooms that need updated lighting | Exterior wiring in Monroe County requires weatherproof fittings and materials rated for freeze-thaw conditions. |
| Electrical Safety Inspections | Full system assessment, Wiring condition review, Panel capacity evaluation, Code violation identification | Landlords, property managers, and buyers or sellers of older Monroe County homes | An inspection gives a clear picture of what the system can handle and what needs attention before it becomes a problem at a tenant's call or a home sale. |
Call (585) 822-6289 and we will walk through what your job involves, confirm the scope, and set the price before anything is scheduled.
(585) 822-6289