Landlords and property managers in Fairport deal with electrical problems differently than a homeowner does. A homeowner can wait a day. A tenant cannot, and a vacant unit with a failed panel or an ungrounded outlet is a unit that cannot be rented. We handle the kind of calls that come with managing a property: code corrections before an inspection, outlet and circuit work between tenants, panel replacements in houses that have not seen an electrician in decades, and repairs that have to be done on a schedule someone else set.
We take those calls for Fairport and handle them the same way we handle every job. The scope is confirmed on the phone, the price is set before the visit, and the work is done to code.
Whether you manage two units or twenty, call (585) 822-6289 and we will get the job on the calendar.
Fairport is a town with a substantial stock of older single-family homes, and older homes generate a particular kind of electrical work. The wiring in many of them was sized for a different era, the panels have not been touched since the house was built, and the outlets in kitchens and bathrooms were never updated for ground-fault protection. The jobs below are what come out of that reality most often.
An electric range or wall oven needs a dedicated 240-volt circuit sized for the load. The same is true of a dryer. When a homeowner replaces an old appliance with a modern one, the existing outlet is often the wrong configuration or the circuit is undersized. We run the circuit properly from the panel, install the correct outlet, and confirm the breaker is rated for the load before the appliance goes in.
Low-voltage work gets overlooked until a renovation is already underway. Doorbell wiring, structured data cabling, and the rough-in for smart-home systems all require planning before the walls close. We handle the rough-in stage so the finish work can go in cleanly. If the doorbell transformer is drawing from a circuit that cannot support it, we address that at the same time.
A panel that is original to a 1960s or 1970s house is not designed for what a modern household puts on it. Breakers that will not hold a reset, a panel that runs warm, or a fuse box that has been patched rather than replaced are all situations that call for a proper assessment. We replace panels, upgrade service capacity, and install subpanels where a garage or addition needs its own distribution point. Load calculations are part of the process so the new panel is sized for what the property actually needs.
Grounding and bonding problems are common in older homes and often surface during a sale inspection or a permit review. We trace the issue, correct the connections, and document the work. Two-prong outlets in an older home are a sign the wiring deserves a look, and we assess what it would take to bring those circuits up to current standards.
Refrigerators, dishwashers, and garbage disposals are supposed to run on dedicated circuits. In practice, many older kitchens have everything sharing a run that was never designed for it. We add dedicated circuits where the panel has capacity and assess whether an upgrade is needed where it does not. The same applies to workshop equipment, hot tubs, and any large appliance that cannot share a circuit without tripping the breaker.
Arc-fault breakers are required in bedrooms and living areas in modern construction, and they are a practical upgrade in any older home where the wiring has not been assessed recently. Ground-fault protection in kitchens, bathrooms, and outdoor locations is a code requirement and a genuine safety measure. We install both as part of repair and renovation work, and we identify where they are missing during an inspection.
Some electrical problems cannot wait. A burning smell near a panel, an outlet that sparks, a partial power loss that cannot be explained by a tripped breaker. We take short-notice work when the schedule allows.
Call (585) 822-6289 and ask what is available. We are open every day from 6:30 AM to 8:00 PM.
A repair that requires shutting down a circuit in an occupied unit or a commercial space needs to be coordinated carefully. We scope the work on the call so you know which circuits will be affected and for how long. That lets you give tenants or staff a clear picture before the electrician arrives, and it means the visit does not run longer than it needs to.
No pressure and no gimmicks, just safe, solid wiring and a schedule that works for the people in the building. One call gets the problem looked at properly.
The price is explained on the call, before anything is scheduled. For most jobs, that conversation covers what the work involves, what it costs, and what the visit includes. You are not agreeing to anything until you know the number.
What can move a quote is what the job turns out to involve once the electrician is on site. The condition of the existing wiring, what has to be opened up to reach a fault, and whether the panel can carry a new circuit without an upgrade are the things that change the scope. If the scope changes, that conversation happens before any additional work continues.
For larger jobs, including panel replacements, whole-home rewiring, and aluminum-wiring remediation, the quote is more detailed because the scope is wider. If you want the longer version, it is on our services page.
Call (585) 822-6289 and we will walk through what the job involves and what it costs.
Older homes in this area often have wiring configurations, panel brands, and outlet styles that are no longer standard. Replacing a breaker in a panel that has not been manufactured for thirty years means sourcing a compatible part rather than reaching for whatever is on the shelf. We identify what the panel takes before the visit so the right part is on hand.
Some components are not stocked locally. If a job requires a part that has to be ordered, we tell you that on the call so you can plan around it. In most cases, common repairs and standard circuit work can be completed in a single visit. Where a part needs to come in, we schedule the return visit at the same time so there is no back-and-forth to arrange it.
The work area is left as it was found, whether the job takes an hour or a full day.
Previous electrical work ranges from solid and code-compliant to wiring that should never have been left in a wall. We assess what is there without assuming the worst. A prior repair that was done correctly stays. One that was not gets corrected. The distinction matters because pulling out wiring that does not need to come out adds cost and time without benefit.
Work that was done without a permit, aluminum branch-circuit wiring with improper connections, knob-and-tube that is still active in walls, and double-tapped breakers that were never corrected are all situations that require proper remediation rather than a patch. We explain what we find and what addressing it involves before any work is agreed. Panel and wiring work is finished to code, and we document what was done so the property has a clear record.
Call in the morning. Talk it through. Know the options by the end of the call.
We serve Fairport and the communities around it throughout Monroe County. That includes Perinton, East Rochester, Penfield, Pittsford, and the areas near St. John Fisher College.
If you are nearby and need electrical work looked at, call (585) 822-6289 and we will confirm whether your address falls within the current service area.
We are available every day from 6:30 AM to 8:00 PM. We'll handle the wiring so you don't have to.
A panel can be physically full, meaning all breaker slots are occupied, or electrically full, meaning the load already on the panel is close to the service capacity even if slots remain. We check both when we assess a panel. A load calculation tells us whether the service can support what you want to add, and we explain the result before any work is agreed.
The process is the same regardless of how many units are involved. You call, we scope the work for each location, and we set a price before anything is scheduled. If units need to be done in sequence or on separate days, we coordinate the schedule on the call so you can plan around it. Repairs, panel work, and code corrections are all handled the same way whether the property has two units or ten.
Outlets and lights in the same room are often on separate circuits, so one can fail while the other stays live. The most common cause is a tripped GFCI outlet upstream that has cut power to every receptacle fed from it. We trace the circuit back to find the source, reset or replace the GFCI if that is the fault, and check the wiring at each affected outlet before the visit is closed out.
Homes built in the 1950s, 1960s, and 1970s commonly have panels, wiring types, and outlet configurations that were never updated. That includes fuse boxes, ungrounded outlets, and in some cases aluminum branch-circuit wiring or knob-and-tube that is still active. An electrical inspection covers the panel condition, the wiring type, and where ground-fault and arc-fault protection is missing.
Call (585) 822-6289 and we can explain what an inspection involves for the property you have in mind.
When the job is finished, the panel is closed, the outlets are tested, and the work area is left the way it was found. That is what every visit should look like, and it is what we aim for on every call we take in Fairport.
Call (585) 822-6289 to get a quote from Irondequoit Electrical Company.
We are open every day from 6:30 AM to 8:00 PM. Call now and we'll set the appointment.
Also serving the towns around: Perinton, East Rochester, Penfield, Pittsford.
From a tripped breaker to a full panel upgrade, we handle the electrical work that keeps Fairport homes and businesses running safely. Every job starts with a clear scope and a confirmed price before anything is scheduled. The table below covers what each service includes, who it fits, and what is practical to know before you call.
| Service Type | Scope of Work | When You Need It | Worth Knowing |
|---|---|---|---|
| Electrical Panel & Service UpgradesMost Popular | 100-amp to 200-amp service upgrades, Subpanel installation, Load calculations, Whole-home surge protection at the panel | Homes adding an EV charger, electric range, or large new load that the current service cannot support | Panel work is finished to code and is the right time to add whole-home surge protection while the panel is already open. |
| Breaker & Fuse Repair | Breakers that trip and won't reset, Fuse box assessment, Replacing failed breakers, Identifying overloaded circuits | Homes where a breaker keeps tripping or a fuse box has not been updated | A breaker that trips repeatedly under normal load is often a sign of a wiring fault or an undersized circuit, not just a bad breaker. |
| Outlet & Switch Installation | Standard and GFCI receptacles, AFCI outlets, Dimmer and three-way switch wiring, USB combination units | Rooms with outdated, ungrounded, or insufficient outlets and switches | Two-prong outlets in an older home are a sign the wiring deserves a look. GFCI outlets can be installed even on ungrounded circuits. |
Call (585) 822-6289 and we will walk through what your job involves, confirm the scope, and set the price before anything is scheduled.
(585) 822-6289