Most electrical problems start small. A breaker that trips once, an outlet that feels warm, a light that flickers when the furnace kicks on. A lot of people reset the breaker and move on, or swap the outlet themselves, and sometimes that is all it takes. The point where that stops making sense is when the symptom comes back, when you cannot trace it, or when what you find inside the box looks nothing like what you expected. That is when calling in someone who does this every day is the right move.
We handle electrical work across Clarkson and the surrounding Monroe County area, from single-circuit repairs to full panel replacements and whole-home rewiring. Homes in a town this size tend to have history: additions wired at different times, outbuildings on their own circuits, panels that have not been touched since the house was built. Whatever the situation, the scope gets confirmed before anything starts, and the price is set before the visit is scheduled.
Call (585) 822-6289 to talk through what you are dealing with.
This question comes up more often than people expect, and it is worth understanding before you call anyone. The utility owns the line that runs to your property and the meter itself. Everything from the meter base inward is your responsibility. When power is out to the whole house, the first check is whether neighboring properties are affected too. If they are, the fault almost certainly sits with the utility and a service call from us will not fix it.
Where it gets less clear is partial power loss. If one side of the house is dark, or specific circuits are dead while others work fine, the fault is more likely inside the panel or the wiring. A tripped main breaker, a failed breaker on a double-pole circuit, or a loose connection at the service entrance can all look like a utility problem from the outside. We can assess that on the call and tell you which direction to go. If it turns out to be a utility issue, we will say so. If it is on your side, we get it on the schedule.
A welder or air compressor draws a load that a standard household circuit was never designed to handle. Running one off a shared circuit trips the breaker and can damage the equipment over time. The fix is a dedicated circuit sized for the actual draw of the equipment, run back to the panel with the right wire gauge and a breaker rated for the load. We size the circuit for the tool, not for the outlet.
Electric ranges, dryers, refrigerators, and chest freezers all benefit from circuits that are not shared. When an appliance is pulling hard and other things on the same circuit start misbehaving, that is the signal. We run the circuit, install the correct outlet, and confirm the panel has the capacity before anything is scheduled.
Older homes in this area often still carry wiring that was never designed for the loads a modern household puts on it. Knob-and-tube and aluminum branch-circuit wiring both require specific approaches: knob-and-tube replacement involves opening walls and running new conductors, while aluminum wiring remediation focuses on the connection points throughout the home. We assess what is present and explain what each option involves before the work is agreed.
Battery-operated alarms are common, but hardwired units on a dedicated circuit with battery backup are more reliable and are required in certain situations. We install interconnected hardwired alarm systems so that when one unit detects smoke or CO, every alarm in the house responds. In homes where the existing alarms are aging or where interconnection is absent, this is a straightforward upgrade with a real safety benefit.
A detached garage or outbuilding that needs more than a single circuit is a good candidate for its own subpanel. Running multiple individual circuits from the main panel to a structure that is any distance from the house gets expensive and impractical fast. A subpanel fed by a single larger run gives the structure its own distribution point and room to grow. We handle the feeder run, the subpanel installation, and the circuits inside the structure.
Grounding and bonding issues rarely show obvious symptoms until something goes wrong. An improperly grounded system or a bonding gap can allow voltage to appear on surfaces that should be at zero potential. Safety inspections surface these issues regularly, and they come up in older homes where the grounding system was installed to a different standard or was never updated after modifications. We identify what is missing and correct it as part of the same visit.
Renovation and extension work has a sequence, and the electrical rough-in has to happen at the right point in it. Framing needs to be complete before wiring can be run through studs and joists. Insulation and drywall come after the rough-in is inspected. Getting that order wrong means opening finished walls, which adds cost and time to everyone's schedule.
When the electrician arrives, the real work begins, and on a renovation that means reading the existing system as well as running new work. An addition that adds load to a panel that is already near capacity needs that issue addressed before the new circuits are energized. A kitchen remodel that moves appliances to new locations needs circuits planned for where things will actually sit, not where they used to be.
We coordinate with the build schedule so the electrical work is done in the right sequence.
If you are managing a renovation and need the electrical scoped and timed around other trades, call (585) 822-6289 and we can work through what the project needs.
Not every property can go dark for half a day. Rental units with tenants, small businesses that need to stay open, and properties where a circuit feeds something that cannot be interrupted all require the work to be planned around the situation. We work through that on the call. If the job needs to happen in stages, or if certain circuits need to stay live while others are worked on, we scope it that way from the start.
Some faults are urgent. A burning smell near a panel, an outlet that sparked and stopped working, a partial power loss that has no obvious cause. These are situations where waiting until next week is not the right answer. We are available every day from 6:30 AM to 8:00 PM.
Scheduling a service call is simple: call (585) 822-6289, describe what you are seeing, and we will confirm what is available. Every job gets treated like it matters, because it does.
Matching hardware to what is already in a property is one of the less-discussed parts of electrical work, and it matters more in older homes. A panel from the 1970s may take breakers that are no longer in standard production. A fixture with a specific mounting configuration may need an adapter or a replacement that fits the existing box. When a part is obsolete, there are usually two paths: find a compatible replacement that meets current standards, or replace the surrounding infrastructure so the repair is done properly rather than patched.
We identify which situation applies before the visit, where possible. If a part needs to be ordered, we tell you that on the call. Standard repairs are often wrapped up in a single visit. Jobs that depend on a specific part may require a follow-up visit, and we confirm that upfront so you can plan around it.
No pressure and no gimmicks, just safe, solid wiring and an honest conversation about what the job requires. There is more on our electrical service list.
That is the question we get on almost every call, and it is a fair one to ask early. The price is set before anything is scheduled. For common jobs, the scope and the rate are confirmed on the call. For more involved work, the price is based on what the job actually requires: what the fault turns out to be, what has to be opened up to reach it, and whether the existing panel and wiring can carry the change without additional work.
The things that move a quote are real and worth understanding. A repair that looks straightforward from the outside sometimes reveals wiring that needs to be addressed before the original fix can be completed. A circuit addition that would be simple in a newer home may require panel work in an older one. If the scope changes once the work is underway, that conversation happens before anything additional is done.
The scope of the electrical work is priced before it starts.
Call (585) 822-6289 and ask what the job involves. You will get a clear answer before the visit is confirmed.
We cover Clarkson and the communities nearby throughout Monroe County. That includes Brockport, Hamlin, Holley, Parma, and Spencerport. If you are in one of those towns and need electrical work looked at, call and we will confirm whether your address falls within the current schedule.
We are available every day from 6:30 AM to 8:00 PM. One call gets the problem looked at properly.
We confirm the timing with the property owner or the general contractor managing the project. Electrical rough-in needs to happen before walls close, and trim-out happens after surfaces are finished. If another trade is involved, we coordinate the sequence so the electrical work does not hold up the rest of the project and the rest of the project does not create access problems for us.
We can assess it and identify what needs to be brought up to current standards. Whether unpermitted work can be signed off depends on the jurisdiction and what the work involves. We explain what we find and what the path forward looks like, and we do not make representations about what a building department will or will not accept.
A panel that buzzes or hums is telling you something is working harder than it should. The sound often comes from a breaker that is failing to trip under an overload, a loose bus connection, or a neutral that has come loose from its terminal. It is not a noise to ignore. Call us and we will assess the panel before the condition worsens.
Describing what you are seeing is enough. A sound, a smell, a circuit that stopped responding, a panel that feels warm. That is what the call is for. We work through it with you, scope what needs to be done, and set the price before anything is scheduled.
Call Irondequoit Electrical Company at (585) 822-6289.
We are available every day from 6:30 AM to 8:00 PM. Call now and we'll set the appointment.
From a tripped breaker to a full panel upgrade, we handle the electrical work that keeps Clarkson homes and businesses running safely. Every job starts with a clear scope and a confirmed price before anything is scheduled. The table below covers what each service includes, who it fits, and what is practical to know before you call.
| Service Type | Scope of Work | When You Need It | Worth Knowing |
|---|---|---|---|
| Electrical Panel & Service UpgradesMost Popular | 100-amp to 200-amp service upgrades, Subpanel installation, Load calculations, Whole-home surge protection at the panel | Homes adding an EV charger, electric range, or large new load that the current service cannot support | Panel work is finished to code and is the right time to add whole-home surge protection while the panel is already open. |
| Backup Generator Installation | Transfer switch installation, Dedicated circuit from panel to generator inlet, Standby and portable hookup configurations, Backfeed prevention wiring | Clarkson homeowners preparing for multi-day winter outages from lake-effect storms | Our scope is the wiring and the transfer switch. The generator itself comes from the homeowner or a separate supplier. |
| Electrical Safety Inspections | Full system assessment, Wiring condition review, Panel capacity evaluation, Code violation identification | Landlords, property managers, and buyers or sellers of older Monroe County homes | An inspection gives a clear picture of what the system can handle and what needs attention before it becomes a problem at a tenant's call or a home sale. |
Call (585) 822-6289 and we will walk through what your job involves, confirm the scope, and set the price before anything is scheduled.
(585) 822-6289